Discovering Essential Plumbing Skills is Crucial for Installing a Bathtub
Discovering Essential Plumbing Skills is Crucial for Installing a Bathtub
Blog Article
The author is making a number of great observations related to How to Install a Bathtub Yourself as a whole in this great article down the page.
Installing a bathtub isn't exactly rocket science, yet it does call for solid plumbing, carpentry, as well as sometimes, tiling skills. Replacing an old tub with a brand-new one is additionally a moderately difficult job. If the old bathtub is readily available, the job can relocate speedily; if you have to open a wall to remove the old tub and place the brand-new bath tub, the job is a lot harder. In either instance, the job is within a house handyman's skills, although you will need an assistant to vacate the old bathtub as well as set in the brand-new one. See to it you have actually qualified yourself for the work and also are comfortable attempting it. As opposed to employing a specialist to take control of a halfway-completed task, it is much better to take into consideration employing one before you begin. Chances are you may require a specialist plumber to make tube links.
This article will help you install a brand-new bath tub in your washroom if you have actually already bought a brand-new bathtub as well as don't require to alter the arrangement of your previous water pipelines.
Your tools and also material list must comprise the following:
Getting ready for the Setup
To start with, the sustaining structure provided with the bathroom must be fitted (if called for) according to the supplier's guidelines. Next off, fit the taps or mixer to the bath tub. When fitting the faucet block, it is necessary to see to it that if the tap comes with a plastic washer, it is fitted between the bathroom as well as the faucets. On a plastic bathroom, it is likewise reasonable to fit a supporting plate under the taps unit to prevent stress on the tub.
Fit the adaptable faucet adapters to the bottom of both taps using 2 nuts and olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet via the hole in the bath. Make use of the nut supplied by the supplier to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. Ensure you make use of all of the supplied washers.
Connect the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom should now be ready to be fitted in its last position.
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your installment, after that the first thing you should do is disconnect the supply of water. After doing so, turn on the taps to drain any water continuing to be in the system. The procedure of getting rid of the existing faucets can be rather problematic due to the limited gain access to that is commonly the situation.
Use a container wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipes to the faucets. Have a towel all set for the staying water that will certainly come from the pipelines. As soon as the supply pipelines have been removed, utilize the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to quit the single taps from transforming throughout this procedure. When the taps have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any kind of old sealing substance.
Before going on to fit the new faucets, compare the pipe connections on the old faucets to the new faucets. If the old taps are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Mounting the Bath tub
Making use of the two wood boards under its feet, put the tub in the needed setting. The wooden boards are helpful in evenly spreading out the weight of the tub over the location of the boards instead of concentrating all the weight onto 4 little factors.
The following goal is to make sure that the bath tub is leveled all round. This can be accomplished by examining the level and adjusting the feet on the tub till the spirit level reads level.
To install faucets, fit all-time low of the outermost adaptable faucet adapter to the suitable supply pipe by making a compression join; then do the same for the various other tap.
Switch on the supply of water and check all joints as well as new pipework for leaks and tighten them if essential. Load the bathtub as well as additionally inspect the overflow outlet and also the normal electrical outlet for leakages.
Lastly, fix the bathroom paneling as described in the supplier's instruction manual. Tiling and securing around the bathtub needs to wait up until the bathtub has actually been made use of a minimum of once as this will resolve it right into its final setting.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will require a plastic adapter to avoid damage to the thread. One end of the adapter fits on the plastic tail of the faucet and the other end gives a link to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly require reducing couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next off, place the tap in the placing opening in the bath/basin making certain that the washing machines are in location between the faucet as well as the sink. Safeguard the faucet in position with the supplier provided backnut. As soon as the faucet is firmly in position, the supply pipelines can be linked to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with regular faucet ports. The former kind must be linked to the tap finishes initially, tightening up only by hand. The supply pipelines can later on be linked to the other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the area where the bathroom satisfies the floor tile, it is needed to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate enough to split an inflexible seal, creating the water to permeate the wall surface between the bathroom as well as the tiling, resulting in complications with moisture and feasible leakages to the ceiling below.
You can pick from a variety of coloured sealants to assimilate your components and fittings. They are offered in tubes and also cartridges, and also are capable of sealing spaces as much as a size of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with twists of soaked newspaper or soft rope. Keep in mind to always load the bath tub with water prior to securing, to permit the movement experienced when the tub is in use. The sealant can break rather early if you do not take into consideration this activity before sealing.
Alternatively, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally easily offered on the market. It is recommended to fit the ceramic tiles using water-resistant or waterproof glue and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you enjoy reading up on Tools You Need to Install a New Bathtub ? Try leaving feedback directly below. We will be interested to see your opinion about this write-up. We hope that you come back again later on. Sharing is good. Helping others is fun. Thanks for your time. Visit us again soon.
Tap dripping? Phone! Report this page